GTO Laser
Dealer: PRECYZJA-TECHNIK
|
 |
- Product description
-
GTO Laser allows you to measure wheel alignment in passenger cars and minivans, as well as light commercial vehicles with rim diameter of 12” to 20”. GTO is a mechanical-laser device; the horizontal angles (partial and total toe, front axle set back and thrust angle) are measured using low-energy, semi-conductor lasers, whereas the vertical angles (camber, caster and king-pin inclination are measured with adjustable air-bubble levels. The use of laser beams makes it possible to work even in direct sunlight; at the same time the lasers are completely safe. The measuring units are powered with new-generation batteries (they have no memory effect); charging and optimised charging takes place when the measuring units are placed back in their docks. It is also possible to power the device with cables, of course.
GTO Laser in its richest, four-unit version allows you to do full alignment, even on salvage vehicles. Thanks to its non-complicated design, the device requires virtually no manufacturer servicing; the user can check the correctness of its indications himself, he just needs a calibration bar and a mirror-checking device.
- Intended use
-
GTO Laser was designed to quickly measure wheel alignment in a variety of vehicles types, with rim diameter ranging from 12” to 20”. Its main asset is the possibility to measure front partial toe with reference to the geometrical drive axis and, while doing so, take front wheel set back into account.
In a single session, the GTO Laser can measure or provide indications necessary for the calculation of the following angles:- Rear camber(*),
- Rear half-toes (*),
- Rear total toe (*),
- Thrust angle (*),
- Caster,
- Front camber,
- King-pin inclination,
- Front half-toes,
- Front total toe,
- Front wheels set-back,
- Wheelbase difference,
- Toe out on turns at 20° steering lock,
- Axle offset (*).
NOTE (*) - only when using the four-unit version of the device.
- Measuring range and accuracy
-
GTO Laser measures the following angles:
Measured parameter Range Accuracy Rear axle Half-toe ± 2° 5' Total toe ± 4° 10' Camber ± 5° 10' Front axle Caster -5° ÷ 18° 10' King-pin inclination -5° ÷ 18° 10' Camber ± 5° 10' Half-toe ± 1°50' 2' Total toe ± 3°40' 4' Set-back ± 3°40' 4' Thrust angle - 10' Steering lock ± 50° 30' Wheelbase difference - 1 mm - Technical data
-
Wheel rim diameter 12" - 20" Voltage 220 V, 50 VA Measuring units voltage - on battery 6V= - on cable 10V= Quick charge maximum time 3 hours Measuring unit minimum working time (fully charged): - on battery 7 hours Laser: - laser type 2 conforming to the PN-EN 60825-1 norm - laser maximum output power do 1 mW - laser beam wave length 670 nm turntable maximum load 10000 N (1000 kG) Key component weight: - front measuring unit 4,5 kg - rear measuring unit 2,5 kg - clamp 3,5 kg - turntable 8,5 kg - wall-mounting/cabinet 7 / 47 kg - complete device with cabinet ~ 160 kg Key component dimensions: - front measuring unit 720x255x230 mm - rear measuring unit 200x230x200 mm - turntable 370x445x55 mm - wall-mounting 390x200x470 mm - cabinet 550x570x940 mm Operating conditions: - indoor operation only - ambient temperature +5° : +40°C - atmospheric pressure 940 hPa -1060 hPa - relative humidity up to 80% in temp. +31°C - permissible voltage fluctuations ± 10% of rated voltage - permissible frequency fluctuations ±1% of rated frequency - ITS certificate
-
GTO Laser is certified to conform to all the standards set by the Motor Transport Institute. The certificate was issued on 03.07.2012 with the number Z/15/076/12.
Conformity Certificate no. Valid Notes Z/15/122/01 01.09.2001-31.08.2004 Z/15/105/04 01.09.2004-31.08.2007 Z/15/035/07 01.09.2007-31.08.2012 Z/15/076/12 01.09.2012-31.08.2017 
- Variants
-
GTO Laser is sold in five versions. It comes with either two or four measuring units, can be cable or battery-powered and wall or cabinet-mounted. The respective versions are configured as follows:
1. Base version – includes two cable-powered measuring units and no wall-mounting or cabinet. 
2. Two-unit wall-mounted version – includes two measuring units and a wall-mounting. 
3. Two-unit cabinet version – includes two measuring units and a cabinet. 
4. Four-unit wall-mounted version – includes four measuring units and a wall-mounting. 
5. Four-unit cabinet version – includes four measuring units and a cabinet. Versions 2-5 are powered cordlessly, using batteries
NOTE: It is possible to upgrade individual versions by purchasing additional components.
- Product configuration
-
Part or component name Number of pieces included 4-unit version
2-unit version Base version Front measuring unit 2 2 2 Rear measuring unit 2 - - Universal clamp 12" - 20" SL 4 2 2 Universal clamp 12" - 20" with 2 sets of special feet 4 2 2 Special foot 16 8 8 Mechanical turntable 2 2 2 Turntable ramp 4 4 4 Cabinet / Wall-mounting 1 1 - Power adapter - - 1 ROC target - front 2 - - ROC target - rear 2 - - Rear target 2 2 2 Break pedal depressor 1 1 1 Steering wheel holder 1 1 1 Short slip plate 2 2 2 Short slip plate base 2 2 2 Reinforced slip plate with ramps 2 2 2 Reinforced long slip plate with ramps 2 2 2 Slip-turn plate with ramps 2 2 2 Control bar 1 1 1 User guide 1 1 1 Mirror calibration unit 1 - - Clamp adapter l=55 mm 4 2 2 Clamp adapter l=100 mm 4 2 2 Measuring unit's protective hook and sling 4 2 2 Power lead 2 2 2 Tape measure 1 1 1 Packaging - wooden pallet 1 1 1 Training film 1 1 1 "GTO PC" 1 1 1 "Autodata" wheel alignment data 1 1 1 NOTE!
- Up-to-date information on which of the above components are included in the standard version of the machine is supplied by the sales department.
- It is possible to upgrade individual versions by purchasing additional components.
- Training film
-
Each device ships with a free CD containing a training video, so that the user can learn to make full use of the equipment. The video takes the technician through the whole process of measuring wheel alignment step-by-step and is a great addition to the user manual.
